Solutions and Mixtures
A solution is a homogeneous mixture of two or more substances. The substance present in the smaller amount is the solute, and the substance present in the ...
Types of Solutions
A solution is a homogeneous mixture of two or more substances. The substance present in the smaller amount is the solute, and the substance present in the larger amount is the solvent. When the solvent is water, the solution is called an aqueous solution. Solutions can be classified by the physical state of their components. Solid in liquid (saltwater), gas in liquid (aerated drinks — CO2 in water), liquid in liquid (alcohol in water), and gas in gas (air) are common examples.
Mixtures can also be heterogeneous (components not uniformly distributed), like sand in water or oil in water. Colloids are intermediate: particles (1-1000 nm) are dispersed in a medium and do not settle, but scatter light (the Tyndall effect). Examples of colloids: milk (fat in water), fog (water droplets in air), smoke (solid particles in air), and jelly (liquid in solid). Suspensions have larger particles (above 1000 nm) that settle on standing, like chalk in water.
Expressing Concentration
Concentration tells us how much solute is dissolved in a given amount of solution or solvent. Common units: Molarity (M) = moles of solute / volume of solution in litres. Molality (m) = moles of solute / mass of solvent in kg. Mole fraction (x) = moles of component / total moles of all components. Mass percent (w/w) = mass of solute / mass of solution x 100. Volume percent (v/v) is used for liquid-liquid solutions.
Molarity changes with temperature (because volume changes), while molality does not (mass is unaffected by temperature). This makes molality more reliable for experiments involving temperature changes. Mole fraction is dimensionless and temperature-independent. For a dilute aqueous solution, molarity and molality are approximately equal because the mass of 1 litre of water is approximately 1 kg.
Solubility and Henry's Law
Solubility is the maximum amount of solute that dissolves in a given quantity of solvent at a specific temperature. For most solid solutes in liquid solvents, solubility increases with temperature. For gases dissolved in liquids, solubility decreases with temperature (this is why warm soda goes flat faster) and increases with pressure.
Henry's Law states that the solubility of a gas in a liquid is directly proportional to the partial pressure of the gas above the liquid: p = KH x x, where p is the partial pressure of the gas, KH is Henry's law constant, and x is the mole fraction of the gas in solution. Henry's Law explains why deep-sea divers get the bends (decompression sickness): when they ascend rapidly, the pressure drops and nitrogen dissolved in blood under high pressure comes out of solution as bubbles, blocking blood vessels.
Colligative Properties
Colligative properties depend only on the number of solute particles (molecules or ions) in a solution, not on their identity. The four colligative properties are: (1) Relative lowering of vapour pressure. (2) Elevation of boiling point: delta Tb = Kb x m, where Kb is the ebullioscopic constant and m is molality. (3) Depression of freezing point: delta Tf = Kf x m, where Kf is the cryoscopic constant. (4) Osmotic pressure: Pi = iMRT, where i is the van't Hoff factor.
Osmotic pressure is the pressure needed to stop osmosis (the flow of solvent through a semi-permeable membrane from a dilute to a concentrated solution). Reverse osmosis (applying pressure greater than osmotic pressure) is used to purify water. The van't Hoff factor i accounts for electrolytes that dissociate: for NaCl (which dissociates into Na+ and Cl-), i = 2, so it has twice the colligative effect of a non-electrolyte at the same molality.
Worked Example and CBSE Exam Tip
Worked Example: Calculate the boiling point elevation when 18 g of glucose (C6H12O6, molar mass 180 g/mol) is dissolved in 100 g of water. Kb for water = 0.512 K·kg/mol. Moles of glucose = 18/180 = 0.1 mol. Mass of solvent = 100 g = 0.1 kg. Molality m = 0.1 / 0.1 = 1 mol/kg. Delta Tb = Kb x m = 0.512 x 1 = 0.512 K. Boiling point = 100 + 0.512 = 100.512 degrees C.
CBSE Exam Tip: Class 12 board exams consistently include numericals on all four colligative properties. Learn the formula for each: delta Tb = Kb x m; delta Tf = Kf x m; Pi = iMRT; and relative lowering of vapour pressure = n2/(n1+n2) approximately n2/n1 for dilute solutions. The van't Hoff factor for strong electrolytes is the number of ions they dissociate into (KCl gives i=2, CaCl2 gives i=3). For weak electrolytes and non-electrolytes, i=1. Abnormal molar mass due to association (e.g., acetic acid in benzene forms dimers, i < 1) is a conceptual question.